manualshive.com logo in svg

D-Link DGS-3312SR, Product Manual

Share
Download
D-Link DGS-3312SR Product Manual Download Page 45

DGS-3312SR Gigabit Layer 3 Switch 

 

Figure 3- 13. Stack Mode Setup (stacking enabled) window 

Variables in this window are described below: 

Parameter  

Description 

ID 

Displays the Switch’s order in the stack. The Switch with a unit id of 1 is the master 
Switch. 

MAC Address 

Displays the unique address of the Switch assigned by the factory. 

Port Range 

Displays the total number of ports on the Switch. Note that the stacking port is 
included in the total count. 

Mode 

Displays the method used to determine the stacking order of the Switches in the 
Switch stack. 

Version 

Displays the version number of the stacking firmware. 

RPS Status 

Displays the status of an optional Redundant Power Supply. 

Model Name 

Displays the model name of the corresponding Switch in a stack. 

When the stacked group is connected and properly configured, the virtual stack appears in the upper right-hand corner of 
the web page. 

32 

Summary of Contents for DGS-3312SR





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands