manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 69 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 69

Service and Maintenance    

65

Cat. No. 01021713

Possible Results

MODEM TEST ERROR

NO TONE!!

MODEM TEST 

NOT POSSIBLE NOW 

TRY LATER!

MODEM EMAIL 

SUCCESS

MODEM TEST  

TIME

SET SUCCESS

Use Data Port

 1) TST WIRELESS

 2) TESTPHONELIN

>3) USE DATA PORT 

 4) TEST APP

10.  Press 

 

 

 to select 3)USE DATA PORT. The screen displays the data re-

port status screen.

MINI REPORT

Sending ...

11.  Press 

 to to send the mini report. 

MINI REPORT

Sent!

12.  The RO controller displays the message delivery status. Press 

 to exit the 

screen. See Appendix A regarding report data.

Test App

 1) TST WIRELESS

 2) TESTPHONELIN

 3) USE DATA PORT 

>4) TEST APP

13.  Press 

 

 

 

 to select 4)TEST APP. This diagnostic is used only for factory 

testing.

TEST APP

OFF

This diagnostic is used only for factory testing.

Summary of Contents for G1 Series















































































































































Reviews:

No comments