Culligan G1 Series Installation, Operation And Service Instructions Download Page 22

Page: 22 / 142

Culligan® Series G1 Reverse Osmosis

Cat. No. 01021713

Pressurized Storage Tank

The product water can be stored in a pressurized storage tank with the reverse osmosis unit controlled by a pressure

switch. Use the same components used for direct feed (see Figure 16). The pressure switch needs to be wired to the con-

trol panel as a float switch (see

Figure 57 on page 105

for G1 standard wiring). A pressurized water storage kit is avail-

able for the G1 under P/N D1013880 (110V) or P/N D1018976 (220V). Connect the product tubing to a bulkhead fitting at

the top of the storage tank such as P/N 01005095 (2-gallon), P/N 01004776 (3-gallon), or P/N 01004765 (9-gallon).

Non-Pressurized Product Water Storage Tank

Depending on the type of application, a level control may be required to turn the unit off when the storage tank is full.

Install the level control according to the instructions provided with the control. See

“GBE RO Controller Basic sub-panel

wiring.” on page 105

for electrical connections.

NOTICE

If a repressurization pump is used, an additional level control is recommended to prevent the

pump from running dry if the storage tank is empty.

To maintain high water quality, a hydrophilic air vent filter, vacuum breaker, pop-off valve, ultraviolet lamp, and pressure

relief valve may be required.

Direct Feed

If the product water is to be used directly, without storage, a few precautions are necessary to prevent damage to the

elements. Install a pressure gauge, pressure relief valve, and a normally-open (“dump”) solenoid in the product water

line as shown in Figure 16, or use pressurized storage kit (P/N D1013880). The pressure gauge will allow the operator to

monitor the product water pressure. The relief valve, which should be set to open at 40 psig, will prevent the product water

pressure from exceeding 40 psi. The dump solenoid will relieve all pressure when the unit is off.

52 6\VWHP

7R 6HUYLFH

7R 'UDLQ

3UHVVXUH *DXJH

3UHVVXUL]HG

6WRUDJH .LW

2SWLRQDO

3UHVVXUL]HG

6WRUDJH

7DQN

8VH RI 3UHVVXUL]HG 6WRUDJH 7DQN UHTXLUHV XVH RI 3UHVVXUL]HG 6WRUDJH .LW '

:KHQ XVLQJ ' \RX PXVW VHW WKH IORDW VZLWFKHV WR EH 1250$//< &/26('

&KHFN

9DOYH

3UHVVXUH 6ZLWFK

Figure 16.

Direct feed connection.

Wire the direct feed/pressurized storage solenoid valve in parallel with the motor.
Valve SV4 closes when the RO pump runs; SV4 opens when the pump stops, allowing all membrane back proessure to

be relieved.

NOTICE

Product back pressure will decrease the net pressure pushing water through the reverse osmosis

elements. Therefore, the flow of product water will decrease.

Summary of Contents for G1 Series















































































































































Search results

Summary of Contents for G1 Series

Reviews:

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 22 / 142

Search results

Summary of Contents for G1 Series

Reviews: