manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 32 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 32

 28 

  

Culligan® Series G1 Reverse Osmosis

 28 

 

Cat. No. 01021713

Wiring for Softeners and Filters with MVP Controller

For these systems, you must add a 24V relay P/N 01016156, to provide the pretreatment contact. 
MVP to Relay: Connect a wire from Terminal 5 of the relay to the left terminal of P8 (Aux 2) on the MVP circuit board. 

Connect another wire from terminal 1 of the relay to the right terminal of P8. Refer to 

Figure 18.

Relay to GBE RO controller: Connect a wire from the POSITION (J2), PIN 3 terminal on the AUX board  to terminal 3 on 

the relay. Connect another wire from the POSITION (J2), PIN 4 terminal on the AUX board to terminal 4 on the relay.

Relay

LCD

SW6 Dip Switch

P3 

Comm

Flow 

Meter

Aqua 

Sensor

P1 

Cam

P8 

Aux2

P5 

Aux1

P7 Sol 

Valve

P9 Power

2.5VAC 24V

P6

Motor

P11 

Battery

GROC BOARD

MVP

Figure 18. 

 MVP to GBE RO controller relays.

Summary of Contents for G1 Series















































































































































Reviews:

No comments