manualshive.com logo in svg

Culligan G1 Series, Installation, Operation And Service Instructions, Page: 68 / 142

Share
Download
Culligan G1 Series Installation, Operation And Service Instructions Download Page 68

 64 

  

Culligan® Series G1 Reverse Osmosis

 64 

 

Cat. No. 01021713

Diagnostics

RUNNING

JAN-01-12 12:01P

1.  From the default home screen, press 

. The screen displays the main menu.

 1) GO TO RUNNING

 2) GO TO OFFLINE

 3) INFORMATION 

>4) SETUP

2.  Press 

 

 

 to scroll to 4) SETUP.

3.  Press 

 to select the SETUP menu.

 3) POWERON MODE 

 4) FLUSH MODES

 5) ACCESSORIES

>6) DIAGNOSTICS

4.  Press 

 

 

 

 

 

 to select 6)DIAGNOSTICS. The screen displays the 

diagnostics menu.

>1) TST WIRELESS

 2) TESTPHONELIN

 3) USE DATA PORT 

 4) TEST APP

5.  The screen displays the diagnostics menu.

Test Wireless Remote

>1) TST WIRELESS

 2) TESTPHONELIN

 3) USE DATA PORT 

 4) TEST APP

6.  Press 

 to select 1)TST WIRELESS. The screen displays the wireless test 

screen.

WIRELESS TEST 

0 / 188

RSSI=5

7.  The screen displays the test number and total number of attempts and the re-

ceived signal strength indicator (RSSI). The system will continue to test the signal 

strength until you press any button to return to the diagnostics menu. 

 

The signal strength indicator (RSSI) will show a value of between 0 and 8.  If the 

RSSI is at least 4, then the installation is complete.  It the SSI drops below 4, then 

it may be necessary to select an alternate location for the wireless remote.

Test Phone Line

 1) TST WIRELESS

>2) TESTPHONELIN

 3) USE DATA PORT 

 4) TEST APP

8.  Press 

 to select 2)TESTPHONELIN. The screen displays the modem test 

screen.

MODEM TEST

Emailing now 

Please Wait ...

9.  Press 

 

 to begin testing the modem telephone line. The screen displays the 

status of the test before displaying the results. Do not press any buttons before the 

test is complete or the controller will return to the Diagnostics menu.

Summary of Contents for G1 Series















































































































































Reviews:

No comments