CTC Union GSW-3208M User Manual Download Page 88

Page: 88 / 148

Chapter 6. Manage / Configure the Switch

all Shows all Trunking Group Configuration

group Shows Each Trunking Group Configuration

show trunk configuration

command is used to show trunk function enable/disable setting.

show trunk all

command is used to show port member settings of all trunk groups.

show trunk group x

command is used to show port member settings of Trunk Group x. (“

” is the trunk group

index.)

27.

show version

command

This command is used to show system version information and model information.

For example,

# show version

Firmware Version: 1.05.00

Number of Ports: 10

Model Name: 10G Switch SNMP Management

28.

show vlan

command

This command is used to show VLAN configuration of the switch.

# show vlan ?

private-vlan Private VLAN

id VLAN interface

name VLAN interface name

port-based Port-Based Virtual LAN Configuration

<cr>

show vlan

command is used to show all 802.1Q VLAN settings (enable/disable, VLAN ID, VLAN Name, VLAN

Type, and Assigned ports).

show vlan id x

command is used to show VLAN setting of VLAN x. (“

” is the VLAN ID).

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands