CTC Union GSW-3208M User Manual Download Page 46

Page: 46 / 148

Chapter 6. Manage / Configure the Switch

username admin www xxx yyy zzz

command is used to set the username and password for administrator. “

www

” is

the old username. “

xxx

” is the old password. “

yyy

” is the new username. “

zzz

” is the new password.

username guest yyy zzz

command is used to set the username and password for guest. “

yyy

” is the new username.

“

zzz

” is the new password.

Administrator is the user who has the right to do configuration modification. Guest is the user who has the right to

view configuration only.

vlan

command

This command is used to enter VLAN configuring mode. And the prompt will become ...

(config)# vlan database

(config-vlan)#

The operations for VLAN are configured in VLAN configuring mode. Please refer to

6.2.5 VLAN Configuring

Commands

section for the details.

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands