CTC Union GSW-3208M User Manual Download Page 102

Page: 102 / 148

Chapter 6. Manage / Configure the Switch

102

The function here is for 802.1x function configuration.

802.1x Authentication Status

: [Enable/Disable/Transparent]

Enable: enable 802.1x function in authentication mode

Disable: disable 802.1x function

Transparent: only forwarding 802.1x packets

Re-authentication (enable/disable)

Timeout Period

and

Max Count

The re-authentication function will re-authenticate users after the timeout period. The Max Count is the maximum

re-try count between the switch and users before authentication fail.

Max Request Count

and

Server Timeout Period

The Server Timeout Period is the timeout period for the request between the switch and RADIUS server.

The Max Request Count is the maximum re-try count between the switch and RADIUS server before

authentication fail.

Supplicant Timeout Period

This is the timeout value between the switch and users (called “supplicant” in 802.1x) after first identification. The

valid value is 0~65535.

Quiet Timeout Period

This is the quiet timeout value between the switch and user before next authentication process when authentication

fails.

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands