CTC Union GSW-3208M User Manual Download Page 26

Page: 26 / 148

Chapter 6. Manage / Configure the Switch

And entering “show ip igmp ?” will get next help message...

# show ip igmp ?

snooping IGMP snooping configuration

And entering “show ip igmp snooping” will get the IGMP settings...

# show ip igmp snooping

IGMP Status: Disable

IGMP Querying: Disable

IGMP Query Interval: 125 seconds

IGMP Report Delay: 15 seconds

IGMP Query Timeout: 255 seconds

If the display is more than one console page, “Esc” can be used to break the display.

For the details, please refer to section

6.2.6 Show commands

calendar

command

This command is used to set the system time. It is entered in <hour minute second month day year> order.

For example,

# calendar set 10 30 0 october 15 2008

# show calendar

Current Time : 2008/10/15-10:30:18

It is 18 seconds passby after the setting command.

10.

configure

command

This command will change the console interface to configure mode. And the prompt will become “(config)#”. In this

mode, administrator can do system configuration of the switch.

The operation of configure mode will be described in next section.

“exit” command can be used to quit this operation mode.

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands