CTC Union GSW-3208M User Manual Download Page 22

Page: 22 / 148

Chapter 6. Manage / Configure the Switch

<< Command Mode >>

There are four command modes for console interface.

General Basic Commands

These are basic commands after login. Users can show switch configueartion/status, ping network device, reboot

switch, ... The prompt is “

xxx#

” for admin user, and “

xxx>

” for guest user.

Configure Mode Commands

With “configure” command, user can enter Configure Mode. Commands in Configuring Mode are for general

switch settings. And its prompt is “

(config)#

”.

Interface Configuring Commands for Port / VLAN Group

If the settings are for ports, it is done with “interface ethernet 1/x” command in configure mode. And the prompt will

become “

(config-if)#

”. For example, “interface ethernet 1/5” is for settings on Port 5.

If the settings are for VLAN group, it is done with “interface vlan x” command in configure mode. And the prompt

will become “

(config-if)#

”. For example, “interface vlan 100” is for settings on VLAN 100.

VLAN Configuring Commands

If the settings are general VLAN settings, it is done with “vlan database” command in configure mode. And its

prompt will become “

(config-vlan)#

”.

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands