CTC Union GSW-3208M User Manual Download Page 120

Page: 120 / 148

Chapter 6. Manage / Configure the Switch

120

1-4). Static 1Q VLAN

This function is used to maintain 802.1Q static VLAN.

Create an 802.1Q VLAN:

Input the VLAN ID and VLAN Name in “Create New Static VLAN”. Click [Create] to create the VLAN. The

valid VLAN ID is 1 ~ 4094.

Select the VLAN in “Modify Static VLAN Table”. The new VLAN is empty by default. You can select ports for

the VLAN. After that, click [Apply] to complete the VLAN configuration.

Modify an 802.1Q VLAN:

Select the VLAN in “Modify Static VLAN Table”.

Modify its setting and click [Apply] to activate the new setting.

Delete an 802.1Q VLAN:

Select the VLAN in “Modify Static VLAN Table”.

Click [Delete] to delete the 802.1Q VLAN.

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands