CTC Union GSW-3208M User Manual Download Page 100

Page: 100 / 148

Chapter 6. Manage / Configure the Switch

100

[Security Policy]

This is used to setup the IP addresses that can manage this switch. They have different access rights set in “Mode”.

And the remote management interfaces (Http/Telnet/SNMP) could be enable/disable for different administrators. This

function is for security policy of switch management.

Note:

Remember to enable at least one IP/Subnet with Modify right for Http/ Telnet/SNMP interface. Otherwise,

configuring switch from remote will become impossible. In that case, you can manage the switch from console only.

2). Mac Security Configuration

There are two Mac ID security modes for the switch. One is Static Mac ID Filter on Port, another is Dynamic Mac ID

Number Limit on Port.

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands