CTC Union GSW-3208M User Manual Download Page 116

Page: 116 / 148

Chapter 6. Manage / Configure the Switch

116

Port Designated Root

: This shows the root bridge ID of this segment and its bridge priority.

Port Designated Cost

: This shows the path cost between the root port and the designated port of the root bridge.

Port Designated Bridge

: This shows the switch’s bridge ID and its bridge priority setting.

Designated Port

: This shows the port number and its port priority..

Port Forward Transitions

: This is the forwarding transition counter on the port.

Port Role

: It is the role of the port for the STP operation. It could be Root, Designated, Backup, or Alternated. If the

port is link down, the port role will be Nonstp.

Point To Point

: This is a Point-to-Point link on the port.

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands