CTC Union GSW-3208M User Manual Download Page 134

Page: 134 / 148

Chapter 6. Manage / Configure the Switch

134

2). Lacp Port Configuration

This page is used to configure LACP function. With LACP protocol, switches can learn trunk connections

automatically.

Follow the steps to do it. (*Don’t connect trunk cables until this function is set.)

Enable Trunk function at “Trunk Information” page first. Then click [Apply].

Assign System Priority. (Its value is 1~65535 and higher number has lower priority. Combining with the Mac

address of the switch, it is used to identify this switch in LACP protocol operation.)

Select ports that will run LACP protocol.

Click [Apply].

Note: If ports are already in static trunk group, they are not allowed to apply as LACP ports. If static ports are selected

as LACP ports, warning message will be prompted when [Apply] is clicked.

3). Lacp Port Status

This is for LACP protocol running status.

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands