CTC Union GSW-3208M User Manual Download Page 37

Page: 37 / 148

Chapter 6. Manage / Configure the Switch

lacp

command

This command is used to configure LACP function of the switch. Entering “lacp ?”, the sub-commands will be

shown.

(config)# lacp ?

system-priority Combined with MAC address to form LAG identifier

lacp system-priority x

command is used to configure the system priority for LACP operation of the switch. Its value

is 1~65535 and higher numbers have lower priority. Combining with the Mac address of the switch, it is used to

identify this switch in LACP protocol operation.

Adding ports to LACP trunk group is by “lacp” command in “Interface Configuring Commands for Port”. Please

refer to Section 6.2.4.1 for the details.

logging

command

This command is used to configure logging function of the switch. The logging function can record events at local

flash or remote log server. Entering “logging ?”, the sub-commands will be shown.

(config)# logging ?

log-level Log level

on Enable logging to all supported destination

remote-log Enable logging to remote host

logging log-level x

command is used define the log level of events. The valid value of “

” is 0~7.

logging on

command is used to enable the logging function. And

no logging on

command is used to disable the

logging function.

logging remote-log

command is used to configure remote logging function. Entering “logging remote-log ?”, the

sub-commands will be shown.

(config)# logging remote-log ?

<1-5> Index

<cr>

logging remote-log

command is used to enable the remote logging function. Events will also be sent to syslog

servers.

no logging remote-log

command is used to disable it.

logging remote-log x host y.y.y.y

command is used to set IP address (y.y.y.y) to syslog server with index x. Up to

five (x=1~5) syslog servers are supported.

Summary of Contents for GSW-3208M





















































































































































Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands

CTC Union GSW-3208M, User Manual

Search results

Summary of Contents for GSW-3208M

Reviews:

Related manuals for GSW-3208M

Brands by name

Popular brands