Crystal CS4231A Manual Download Page 33 | Manualshive

Page: 33 / 76

background image

C2SL

Clock 2 Source Select: This bit selects
the clock source used for the audio
sample rates for both capture and
playback. If only one crystal is sup-
plied in hardware, it must be XTAL1.
CAUTION: C2SL can only be
changed while MCE (R0) is set.

0 - XTAL1

Typically 24.576 MHz

1 - XTAL2

Typically 16.9344 MHz

CFS2-CFS0

Clock Frequency Divide Select: These
bits select the audio sample fre-
quency for both capture and
playback. The actual audio sample
frequency depends on which clock
source (C2SL) is selected and its fre-
quency. Frequencies listed as N/A
are not available because their sam-
ple frequency violates the maximum
specifications; however, the decodes
are available and may be used with
crystals that do not violate the sam-
ple frequency specifications.
CAUTION: CFS2-CFS0 can only be
changed while MCE (R0) is set.

S/M

Stereo/Mono Select: This bit deter-
mines how the audio data streams
are formatted. Selecting stereo will
result in alternating samples repre-
senting left and right audio channels.
Mono playback plays the same
audio sample on both channels.
Mono capture only captures data
from the left channel. In MODE 1,
this bit is used for both playback and
capture. In MODE 2, this bit is only
used for playback, and the capture
format is independently selected via
I28. MCE (R0) or PMCE (I16) must
be set to modify S/M. See

Changing

Audio Data Formats section for
more details.

0 - Mono
1 - Stereo

The C/L, FMT1, and FMT0 bits set the audio data
format as shown below. In MODE 1, FMT1, which is
forced low, FMT0, and C/L are used for both play-
back and capture. In MODE 2, these bits are only
used for playback, and the capture format is inde-
pendently selected via register I28. MCE (R0) or
PMCE (I16) must be set to modify the lower four bits
of this register. See

Changing Audio Data Formats

section for more details.

This register’s initial state after reset is: 0000000.

Fs and Playback Data Format (I8)

D7

D6

D5

D4

D3

D2

D1

D0

FMT1 FMT0 C/L S/M CSF2 CFS1 CFS0 C2SL

XTAL1

XTAL2

Divide

24.576 MHz

16.9344 MHz

0 - 3072

8.0 kHz

5.51 kHz

1 - 1536

16.0 kHz

11.025 kHz

2 - 896

27.42 kHz

18.9 kHz

3 - 768

32.0 kHz

22.05 kHz

4 - 448

N/A

37.8 kHz

5 - 384

N/A

44.1 kHz

6 - 512

48.0 kHz

33.075 kHz

7 - 2560

9.6 kHz

6.62 kHz

FMT1

†

FMT0 C/L

D7

D6

D5

0

0

0

Linear, 8-bit unsigned

0

0

1

µ

-Law, 8-bit companded

0

1

0

Linear, 16-bit two’s
complement, Little Endian

0

1

1

A-Law, 8-bit companded

1

0

0

RESERVED

1

0

1

ADPCM, 4-bit, IMA compatible

1

1

0

Linear, 16-bit two’s
complement, Big Endian

1

1

1

RESERVED

† FMT1 is not available in MODE 1 (forced to 0).

CS4231A

DS139PP2

33

«
...
31
32
33
34
35
...
»

Summary of Contents for CS4231A













































































Reviews:

No comments

Related manuals for CS4231A

Brand: K-array Pages: 20

Brand: Teac Pages: 2

Brand: K-Systems Pages: 9

Brand: Interroll Pages: 54

Brand: Coby Pages: 3

Brand: Fender Pages: 51

Brand: Saltillo Pages: 2

AUDEMAT FM PROBE

Brand: Worldcast Systems Pages: 80

Brand: iRobot Pages: 7

151 Musiccenter

Brand: Burmester Pages: 20

Brand: Powerdist Pages: 7

Brand: McIntosh Pages: 32

Brand: Sharp Pages: 68

Brand: Sharp Pages: 112

Brand: RCA Pages: 19

Brand: BXB Electronics Pages: 19

Brand: Ultrasonic Pages: 72

Brand: Trevi Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands