manualshive.com logo in svg

CRS F3, User Manual

Share
Download
CRS F3 User Manual Download Page 95

Chapter 10: Preventive Maintenance

81

99-05-31

Amplifier Communications Failure

As mentioned above, the F3 system is driven by intelligent amplifier modules

embedded in the robot itself. Each module, in addition to regulating the
position of three joints and the current going into the corresponding motors,
performs a number of diagnostic checks at startup and during continuous
operations.

Upon detection of an error or failure, an amplifier module may shut down
motor power as well as communications with the controller. When one

module goes into such a state, the controller will shut down power to the
whole system.

If an amplifier fails to communicate with the controller at startup, the error
is reported on the terminal screen. During normal operations, the health
status of the amplifier modules can be verified with the ampstat command.

The conditions that cause an F3 amplifier module to go into the above
described failure mode are:

1.

 

A blown fuse.

 

Check all the fuses on the front panel of the controller using a
multimeter (visual inspection may be deceptive). Replace any blown fuse
with the corresponding spare provided. Replace the spare.

2.

 

High voltage is detected upon amplifier startup and before the user
turns on the arm power switch.

 

This may be a result of the high power relays in the controller becoming
welded. One way to confirm this is to turn off the controller, remove an
arm power fuse and turn the controller back to verify whether the error

state persists. If it does not, this confirms that one or more of the relays
is welded. Contact the CRS Customer Support Group for instructions on
how to release the relay(s).

3.

 

One of the amplifier modules, or a wire harness leading to it, has
failed, but the other one remains healthy.

 

The ampstat command will indicate the health of both amplifiers. If one

is reported to be working while the other is not communicating, contact
the CRS Customer Support Group for further instructions.

4.

 

There is a breakdown in the F3 servo network, either in the
umbilical or the wire harness, leading to the failure of both amplifier
modules.

The F3 servo network consists of the two amplifier modules as well as the
SGIO board which controls the end-of-arm tool (air or servo gripper) and
the end–of-arm I/O channels. To assess the extent of the network failure,
command the gripper to open or close. If it does not respond, the
problem is a failure in the network that affects all modules.

Summary of Contents for F3

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands