manualshive.com logo in svg

Control Techniques FM-3, Reference Manual

The Fostex FM-3 is an exceptional audio mixer with various customizable features. Unlock its full potential by downloading the comprehensive Owner's Manual for free from our website. This manual provides detailed instructions and allows easy access to all the essential information you need for maximizing your audio mixing experience.

Share
Download
background image

35

Setting Up Parameters

Motor Position Group

Position Command

Position command is the commanded motor position sent to the drive by the FM-3 module. 
This parameter does not take following error into account. See also PosnFeedback and 
FollowingError. Units are in user units.

Position Feedback

Feedback position is the actual motor position in user units.  PosnCommand minus the 
PosnFeedback is the FollowingError

Following Error

The Following Error is the difference between the Position Command and the Position 
Feedback. It is positive when the Position Command is greater than the Position Feedback.

Encoder Position

Motor encoder position in encoder counts.  This position reflects the feedback position of the 
motor and is not scaled into user units. This is a signed 32 bit value.

Motor Velocity Group

Velocity Command

The Velocity Command is the velocity that the FM-3 module is commanding the motor to run 
at. This command is generated by the drive velocity control loop and position loop. It is 
displayed in user units. 

Velocity Feedback

This is the feedback (or actual) velocity. It is calculated using the change in position of the 
motor encoder. It will always return the actual motor velocity - even in synchronized 
applications in which the master axis is halted during a move.

Control Loop Group

Changing the Trajectory Update Rate can have a major effect on the performance of your 
servo system. A longer trajectory update rate means that more time is available to process user 
programs. A shorter update rate means that the control loop is updated more often and 
provides the most accurate performance. Without proper diagnostics, it can be impossible to 
tell how much time is being consumed by the control loop update, and how much time is 
available to run user programs. 

The Control Loop group of parameters on the  Status Online tab shows the user how much 
time is available to run programs. There are two parameters available to help with this. They 
are as follows:

Summary of Contents for FM-3





































































































































































































































































































Reviews:

No comments

Related manuals for FM-3

Vacon NX series Maintenance Manual preview
NX series
Brand: Vacon Pages: 64
Dahua NKB User Manual preview
NKB
Brand: Dahua Pages: 58
Pando PI3300 Instructions For Use Manual preview
PI3300
Brand: Pando Pages: 43
Yamaha disklavier DKC-850 Quick Start Manual preview
disklavier DKC-850
Brand: Yamaha Pages: 2
Black Horse Model BH33-B Instruction Manual Book preview
BH33-B
Brand: Black Horse Model Pages: 19
Grundfos MIXIT Integration Manual preview
MIXIT
Brand: Grundfos Pages: 23
Sungrow EyeM4A Quick Manual preview
EyeM4A
Brand: Sungrow Pages: 4
Apex Toys AM08S Manual preview
AM08S
Brand: Apex Toys Pages: 7
SMC Networks VP31 5 Series Operation Manual preview
VP31 5 Series
Brand: SMC Networks Pages: 15
National Instruments PXIe-8861 User Manual preview
PXIe-8861
Brand: National Instruments Pages: 22
Sames Inocoat Inobox Instruction Manual preview
Inocoat Inobox
Brand: Sames Pages: 84
G-Force UNDER CONTROL CP-28 User Manual preview
UNDER CONTROL CP-28
Brand: G-Force Pages: 2
KATO VISION KT-410C User Manual preview
KT-410C
Brand: KATO VISION Pages: 23
Patton SmartNode 5501 User Manual preview
SmartNode 5501
Brand: Patton Pages: 56
Watts Vision BT-A02 RF Description And Application Manual preview
Vision BT-A02 RF
Brand: Watts Pages: 19
Burkert 20010867 Operating Instructions Manual preview
20010867
Brand: Burkert Pages: 42
Clemco TLR-50 Operating Manual preview
TLR-50
Brand: Clemco Pages: 14
Calian SatService sat-nms VLC Installation Manual preview
SatService sat-nms VLC
Brand: Calian Pages: 40

Brands by name

Popular brands

Load more brands