Condair GC 130 Operation And Maintenance Manual Download Page 43

Page: 43 / 72

Operation

Condair GS

xxxxxxx_A_EN_1905_Condair-GS_OM

5.2.4 Remote Monitoring

The Condair

GS humidifier can be monitored remotely through the remote fault board wired to a remote

monitoring system.

Table 7

describes the function of each relay when triggered.

Table 7: Remote Relay Function

Remote Relay

Description

Error

The humidifier is stopped due to a fault condition, or may be oper

able only for a limited period of time.

Service/Warning

Depending on the software configuration, indicates that a service

warning or a system warning/notification is active.

Unit On

The humidifier has power, and the On/Off switch is in the On

position.

The Condair

GS humidifier can also be monitored remotely from a laptop or desktop computer using

the ethernet port on the integrated control board. Contact your Condair representative for assistance.

5.2.5 Inspections During Operation

Perform regular inspection of the

Condair

GS humidifier and the humidification system when it is in

operation. Inspect the following:

Check the gas connection for any leaks.

Check the water, drain and steam connections for any leakages.

If applicable, check the humidifier and other system components have not shifted from their mount

ings, and are fastened securely.

Check for leaks in the exhaust vent. Check that there are no obstructions anywhere in the exhaust

vent, including the exhaust terminal.

Keep the area around the air intake in the unit clear of all obstructions. If an air intake vent is used,

check for leaks and obstructions in the vent, including the intake terminal.

Check the area around the unit is clear of all insulating and combustible materials.

Visually check the electrical wiring for any damage.

Check the Home screen on the humidifier for service or system warning messages.

If any irregularities (leakages, fault messages or damaged components) are found, shut down the

Condair

GS humidifier before performing service – refer to

"Shutting Down" on page 45

. Contact your Condair rep

resentative if assistance is required.

Summary of Contents for GC 130









































































Search results

Summary of Contents for GC 130

Reviews:

Related manuals for GC 130

Brands by name

Popular brands

Condair GC 130, Operation And Maintenance Manual

Search results

Summary of Contents for GC 130

Reviews:

Related manuals for GC 130

Brands by name

Popular brands