Condair GC 130 Operation And Maintenance Manual Download Page 39

Page: 39 / 72

Operator Interface

Condair GS

xxxxxxx_A_EN_1905_Condair-GS_OM

Software Settings Tab

–

Load Contact Info Page:

allows you to automatically insert contact

information (for technical support) in the unit, from a USB memory

stick. This information is shown when selecting Help on the Home

Screen. Information includes Company Name, Address, Telephone

Number, Email, and Website. Please contact your Condair representa

tive for assistance with this.

–

Manually Load Contact Info:

allows you to manually enter the

Company Name, Address, Telephone Number, Email, and Website,

that will appear when the user selects Help from the Home Screen.

–

Load Logger Definition:

allows you to load a logger definition file

from a USB drive to save data (CSV file) on the USB while the unit

is functioning. A factory supplied access file is required to enable

operation. The interval between recordings can be changed from

the Engineering menu (see your Condair representative).

–

Backup Parameters to USB:

saves the current value of all persis

tent parameters from a certain integrated controller to USB (XML

file).

–

Restore Parameters from USB (selected):

loads the persistent

paramters (XML file) from USB to an integrated controller.

–

Restore Factory Defaults

: Return the GS software settings to

values set at the factory.

4.3

Software Configuration

The Condair

GS humidifier is shipped fully configured from the factory to suit your site-specific require

ments, but this can be modified as needed. This section provides the necessary instructions to recon

figure the control software.

4.3.1

Configuring the Control Software

Perform the basic setup of the control software as follows, if necessary:

1. Make sure that all control wiring and jumpers are installed as described in "External Connections"

in the Installation Manual.

2. Set up the following parameters:

Source

– select the type of control signals to the humidifier ("Analog", "Modbus", "BACnet/IP", etc.,).

Select "Analog" if a sensor/transducer signal or a demand signal from an external P/PI (pro

portional)/(proportional-integral) controller is wired directly to the humidifier. Otherwise, select

an applicable digital communication protocol from the list. If your humidifier has the optional

Lonworks or BACnet (BTL) module installed, select "Modbus".

Control Channels

– select the number of control channels.

Select "Dual" if controlling the humidifier with a high limit and a control signal; otherwise set to

"Single".

Control Mode

– select the general control mode for the incoming control and high limit signal ("De

mand", "RH P", "RH PI", or "On/Off").
Select "Demand" if the control signal is a demand signal from an external controller. Select "RH

P" or "RH PI", as appropriate, if the control signal is from a sensor/transducer. Or select "On/

Off" if the control signal is from an external On/Off humidistat.
Signal Type – select the signal type of the incoming control signal if

Control Mode

is set to "De

mand", "RH P" or "RH PI", and signal

Source

is set to "Analog".

Summary of Contents for GC 130









































































Search results

Summary of Contents for GC 130

Reviews:

Related manuals for GC 130

Brands by name

Popular brands

Condair GC 130, Operation And Maintenance Manual

Search results

Summary of Contents for GC 130

Reviews:

Related manuals for GC 130

Brands by name

Popular brands