manualshive.com logo in svg

Condair GC 130, Operation And Maintenance Manual

Share
Download
Condair GC 130 Operation And Maintenance Manual Download Page 19

19

Operator Interface

Condair GS

 

xxxxxxx_A_EN_1905_Condair-GS_OM  

Operational Status Tab

 

–

Output:

 shows the current actual steam output level of the 

humidifier.

 

–

Operating Hours:

 shows the current accumulated number of hours 

the humidifier has been producing steam since startup.

 

–

Weighted Hours:

 shows the number of operating hours on the unit 

weighted x demand % output.

 

–

Average Demand:

 shows the time-averaged demand on the 

system.

 

–

Service Hours:

 shows the service interval. 

 

–

Est(imated) Days to Service:

 shows the number of days before 

the unit is due for service.

Control Status Tab

 

–

Demand:

 shows the calculated demand for the unit as a percent

-

age of its maximum capacity.

 

–

Linkup:

 shows the humidifier's 'position' in the linkup chain. Select 

to set the humidifier 

 

–

Safety Loop:

 shows the current status of the On/Off devices in the 

safety loop. If the loop is open, the unit will not produce steam.

 

–

Manual Capacity: 

shows the capacity limitation value as a per

-

centage of the maximum capacity of the unit. Select the field to set 

a fixed maximum output capacity.

 

–

Channel 1:

 shows the input signal for Channel 1. If configured for 

demand control, it represents the demand. If configured for RH(P/

PI), it represents sensed humidity.

 

–

Setpoint Channel 1:

 shows the current fixed humidity setpoint 

value for the unit. Select the field to adjust the setpoint value. Refer 

to 

"PI Control Parameters Tab" on page 26 

for more details.

Note:

 

This field appears only if 

Control Mode 

is set to "RH P" or "RH PI".

 

–

Channel 2:

 shows the input signal for Channel 2. If configured for 

demand control, it represents the demand. If configured for RH(P/

PI), it represents sensed humidity.

Note:

 This field appears only if the 

Control Channels 

is set to "Dual".

 

–

Setpoint Channel 2:

 shows the high limit setpoint value for the 

unit. Select the field to adjust the value.

Note:

 This field appears only if 

Control Mode 

is set to "RH P" or "RH 

PI", and 

Control Channels 

is set to "Dual".

Summary of Contents for GC 130









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands