Comtrol RocketLinx ES7528 User Manual Download Page 98

Page: 98 / 144

98 - RocketLinx ES7528 Industrial Managed PoE Rack Mount User Guide

: 2000509 Rev. A

GMRP Configuration

GARP Multicast Registration Protocol (GMRP) is a Generic Registration Protocol

(GARP) application that provides a multicast traffic management facility at layer 2

similar to what IGMP provides at layer 3. GMRP and GARP are industry-standard

protocols first introduced as part of IEEE 802.1D.

GMRP

Configuration

Description

GMRP Protocol

Enable

Disable

GMRP protocol.

Port

The port number.

State

The state of the GMRP operation on this port. The value

enabled indicates that the GMRP is enabled on this port as

long as the GMRP protocol is also enabled for this device.

When disabled, but the GMRP protocol is still enable for the

device, GMRP is disabled on this port.

Apply

Click

Apply

to apply the settings.

Note: You must Save the settings (Page 137), if you want to

maintain these settings if the RocketLinx ES7528 is
powered off.

Summary of Contents for RocketLinx ES7528

















































































































































Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands

Comtrol RocketLinx ES7528, User Manual

Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands