Comtrol RocketLinx ES7528 User Manual Download Page 51

Page: 51 / 144

Storm Control

RocketLinx ES7528 Industrial Managed PoE Rack Mount User Guide

: 2000509 Rev. A

- 51

Storm Control

The Storm Control is similar to Rate Control. Rate Control filters all the traffic over the threshold you input by the user

interface. Storm Control allows you to define the rate for specific Packet Types.

Apply

Click

Apply

to apply the settings.

Note: You must Save the settings (Page 137), if you want to maintain

these settings if the RocketLinx ES7528 is powered off.

Storm Control

Description

Broadcast

To enable or disable broadcast storm control on this port.

Choose Enable/Disable to enable or disable the storm control of

specific port.

DLF

To enable or disable destination lookup failure storm control on

this port.

Multicast

To enable or disable multicast storm control on this port.

Rate (packet/sec) These columns allow you to manually assign the limit rate of the

port. The unit is packets per second. The limit range is from 1 to

262143 packet/sec, zero means no limit. The maximum available

value of Fast Ethernet interface is 148810, this is the maximum

packet number of the 100M throughput.

Apply

Click

Apply

to apply the settings. It may take some time and the

web interface may become slow, this is normal condition.

Note: You must Save the settings (Page 137), if you want to

maintain these settings if the RocketLinx ES7528 is
powered off.

Rate Control

Description

Summary of Contents for RocketLinx ES7528

















































































































































Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands

Comtrol RocketLinx ES7528, User Manual

Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands