Comtrol RocketLinx ES7528 User Manual Download

Page: 60 / 144

60 - RocketLinx ES7528 Industrial Managed PoE Rack Mount User Guide

: 2000509 Rev. A

PD Status Detection

The following graphic illustrates how to configure IEEE 802.3at LLDP. Assume the PD is ready for the configuration for IEEE

802.3at LLDP, you only need to confirm the RocketLinx ES7528 configuration.

For example, connect the port of the RocketLinx ES7528 to the PD (ex. Port 4), set

PoE Mode

Enable

and

Powering Mode

802.3at(LLDP)

. When the RocketLinx ES7528 and the PD are ready to IEEE802.3at LLDP, IEEE 802.3at LLDP starts

operation. Refer to

PoE Status

on Page 61, to see the

PoE Status

page.

PD Status Detection

The RocketLinx ES7528 delivers a useful function – PD Status Detection. This

provides automatic detection of a remote device powered by the RocketLinx

ES7528. If the remote system crashes or is unstable, the RocketLinx ES7528

performs a system reboot by turning off and on again to trigger the remote

device. The following figure shows the web configuration interface for Power

over Ethernet PD Status Detection.

Apply

Click

Apply

to apply the settings.

Note: You must Save the settings (Page 137), if you want maintain these settings if the

RocketLinx ES7528 is powered off.

PD Status Detection

Description

PD Status Detection

Enable

Disable

PD Status Detection function.

IP Address

Type in the IP address that you want to detect.

Cycle Time(s)

This is the gap per detection in seconds.

Apply

Click

Apply

to apply the settings.

Note: You must Save the settings (Page 137), if you

want maintain these settings if the
RocketLinx ES7528 is powered off.

PoE Control

Description

DO NOT TOUCH DEVICE SURFACE DURING

PoE PROGRESS HIGH POWER FEEDING.

Summary of Contents for RocketLinx ES7528

















































































































































Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands

Comtrol RocketLinx ES7528, User Manual

Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands