Comtrol RocketLinx ES7528 User Manual Download Page 96

Page: 96 / 144

96 - RocketLinx ES7528 Industrial Managed PoE Rack Mount User Guide

: 2000509 Rev. A

IGMP Snooping

Use this page to enable the IGMP Snooping feature, assign IGMP Snooping for specific VLANs, and view the IGMP

Snooping table from a dynamic learnt or static that you provide. The RocketLinx ES7528 supports IGMP snooping V1/V2/V3

automatically and IGMP query V1/V2.

IGMP has three fundamental types of messages as follows:

IGMP Snooping

Description

IGMP Snooping

You can select

Enable

Disable

. After enabling IGMP Snooping, you can

then enable IGMP Snooping for specific VLAN.

You can

Enable

IGMP Snooping for some VLANs so that some of the

VLANs support IGMP Snooping and others will not.

To assign IGMP Snooping to VLAN, click the check box of the VLAN ID or

click the

Select All

check box for all VLANs and then click

Enable

. You can

also

Disable

IGMP Snooping for certain VLANs using the same method.

IGMP Snooping Table

This table displays the multicast group IP address, VLAN ID it belongs to,

and member ports of the multicast group. The RocketLinx ES7528 supports

256 multicast groups. Click

Reload

to refresh the table.

Message

Description

Query

A message sent from the querier (IGMP router or switch) asking for a

response from each host belonging to the multicast group.

Report

A message sent by a host to the querier to indicate that the host wants to be or

is a member of a given group indicated in the report message.

Leave Group

A message sent by a host to the querier to indicate that the host has quit being

a member of a specific multicast group.

Summary of Contents for RocketLinx ES7528

















































































































































Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands

Comtrol RocketLinx ES7528, User Manual

Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands