Comtrol RocketLinx ES7528 User Manual Download Page 121

Page: 121 / 144

Event Selection

RocketLinx ES7528 Industrial Managed PoE Rack Mount User Guide

: 2000509 Rev. A

- 121

Event Selection

System Event

Warning Event is sent when….

Device Cold Start

Power is cut off and then reconnected.

Device Warm Start

Reboot the device by CLI or Web UI.

Authentication failure

An incorrect password, SNMP Community String is entered.

Time Synchronize Failure

Accessing the NTP Server is failing.

Fault Relay

The DO/Fault Relay is on.

Super Ring Topology

Changes

Master of Super Ring has changed or backup path is activated.

SFP DDM Failure

The information read from the DDM SFP transceiver is over

temperature or out the range of TX/RX power.

Power Failure

Power (AC, DC1, DC2 or Any) is failure.

Port Event

Warning Event is sent when…..

Link-Up

The port is connected to another device

Link-Down

The port is disconnected (e.g. the cable is pulled out, or the

opposing devices turns down)

Both

The link status changed.

PoE Powering Event

Warning Event is sent when…..

Enable

The PoE port is powering.

Disable

The PoE port is not powering.

Apply

Click

Apply

to apply the settings.

Note: You must Save the settings (Page 137), if you want to

maintain these settings if the RocketLinx ES7528 is
powered off.

Summary of Contents for RocketLinx ES7528

















































































































































Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands

Comtrol RocketLinx ES7528, User Manual

Search results

Summary of Contents for RocketLinx ES7528

Reviews:

Related manuals for RocketLinx ES7528

Brands by name

Popular brands