background image

 

 

16 

 

Section 3 

 

Maintenance 

 

WARNING 

THESE SERVICE INSTRUCTIONS ARE FOR USE BY QUALIFIED PERSONNEL ONLY.  TO 

AVOID ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING OTHER THAN THAT 

CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO 

SO. 

 

Introduction 

 

This  section  of  the  manual  contains  maintenance  information  for  the  Model  GF-30AC-T  High  Current 
Ground Tester.  This maintenance information  is divided into service information, general maintenance, 
a performance test, and a calibration procedure.  The performance test is recommended as an acceptance 
test  when  the  instrument  is  first  received,  and  later  as  a preventative maintenance tool to verify proper 
instrument operation.  A 1-year calibration cycle is recommended to maintain the specifications given in 
Section 1.  The Test equipment required for both the performance test and calibration is a DMM able to 
read true rms 0-3 VAC   1%.   

 

Service Information 

 

The GF-30AC-T is warranted to the original purchaser for a period of 1 year .  This warranty does not 
cover problems due to misuse or neglect.  
 
Malfunctions  which  occur  within  the  limits  of  the  warranty  will  be  corrected  at  no  charge.    Mail  the 
instrument post paid to the manufacturer.  Dated proof of purchase is required for all in-warranty repairs.   
 
The  manufacturer  is  also  available  for  calibration  and  /  or  repair  of  instruments  that  are  beyond  their 
warranty period.  Contact the manufacturer for a cost quotation.  Ship the instrument and your remittance 
according to the instructions given by the manufacturer. 

 

General Maintenance 

 

Interior Access 

 

NOTE 

To avoid contaminating the PWB with oil from your fingers, handle it by the edges or wear gloves.  If the 
PWB becomes contaminated, refer to the cleaning procedures given later in this section. 

 

Summary of Contents for GF-30AC-T




















Reviews: