background image

 

 

13 

2.  Plug  the  split  end  plug  of  the  10  AWG  Test  return  lead  into  the  Return  Lead  Receptacle  of  the 

Tester. 

3.  Plug the Test Power Cord or non-detachable EUT power cord into the Test Power Receptacle of the 

Tester, and then into the power inlet of the equipment to be tested. 

4.  Connect the alligator clip end of the Test Return Lead to the chassis of the equipment to be tested. 
5.  Push  the  test  button.    (If the GF-30AC-T duration control has been set according to the calibration 

procedure, the test will automatically continue for the duration set in the calibration procedure.  If the 
duration control of the GF-30AC-T is set to zero, the test will continue only as long as the test button 
is pressed.) 

6.  The result of the test will be shown by a combination of lights and a buzzer.  Results are interpreted 

below and in a truth table on the rear of the instrument. 

 

Test results 

 
Green  Light:      A  green  light  indicates  the  ground  system  of  the  EUT  has  less  than  100  milliohm 
resistance.  For most categories of equipment, this result is acceptable. 
 
Red Light:   A red light indicates the ground system of the EUT has more than 100 milliohm resistance.  
If a red light occurs, the grounding circuit of the EUT should be reworked and then retested.

 

 
Red  Light  and  Buzzer  Sound:      A  red  light  and  a  buzzer  sound  indicates  an  open  grounding  circuit 
condition.  Check the test lead connections, correct, and retest.  If the test lead connections are correct, a 
red  light  and  buzzer  sound  indicates  an  open  grounding  connection  within  the  EUT.    The  grounding 
circuit of the EUT should be reworked and then retested. 
 
Simultaneous  Red  and  Green  Light:    A  simultaneous  red  and  green  light,  with  or  without  the  buzzer 
sound indicates the resistance of the ground circuit of the EUT is exactly at the pass/fail point.   
 
Green Light and Buzzer Sound:  If you obtain a green light and buzzer test result, the GF-30AC-T is not 
generating  full  test  current.    The  GF-30AC-T  will  report  unreliable  test  results.    Service  is  required.  
Discontinue use of the tester immediately.  

 

Summary of Contents for GF-30AC-T




















Reviews: