Cognex In-Sight 7600 Reference Manual Download

Page: 91 / 113

External Light Connector

The vision system's LIGHT connector is used to connect the External Light cable to an external lighting device, providing

power and strobe control. The External Light cable can be connected to either a continuous or strobed lighting device.

Before using an external lighting device, you must configure the light settings within In-Sight Explorer. For more

information, refer to the Light Settings topic in the

In-Sight ® Explorer Help

file.

Pin#

Signal Name

Wire Color

+24VDC

Brown

Intensity Control

White

GND

Blue

Strobe

Black

Chassis

Not Connected

Note

Cables are sold separately.

Current load: 750 mA maximum. Only the +24VDC pin is capable of sourcing 750mA.

Intensity Control is an analog signal that ranges from 0 to +10VDC, and is configurable within In-Sight

Explorer. It is a control signal only, and must not be used to power an external device. Power should be

sourced from +24VDC and GND. Verify the External Light cable and light support intensity control.

The Strobe output is active low 0VDC and active high +12VDC, with the Polarity configurable within In-Sight

Explorer. It is a control signal only and may not to be used for power. Power should be sourced from

+24VDC and GND.

Specifications

Summary of Contents for In-Sight 7600


















































































































Search results

Summary of Contents for In-Sight 7600

Reviews:

Related manuals for In-Sight 7600

Brands by name

Popular brands

Cognex In-Sight 7600, Reference Manual

Search results

Summary of Contents for In-Sight 7600

Reviews:

Related manuals for In-Sight 7600

Brands by name

Popular brands