manualshive.com logo in svg

Cisco Catalyst 9400 Series, Hardware Installation Manual

Share
Download
Cisco Catalyst 9400 Series Hardware Installation Manual Download Page 93

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement

1030

Warning

No user-serviceable parts inside. Do not open.

Statement 1073

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

Before you begin

You may need a Phillips-head screwdriver to loosen the captive installation screws.

Procedure

Step 1

Ready the replacement fan tray.

When you remove and replace a fan tray in a system that is powered on, there is a time constraint.
So it is important to complete this first step before you remove the fan tray from the front of the
chassis.

Important

a) Remove the replacement fan tray from the shipping packaging.
b) Use a Phillips-head screwdriver and loosen the two captive installation screws on the front panel of the

replacement fan tray (the side with the fan STATUS LED), to detach it from the adapter module.

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

87

Removing and Replacing FRUs

Removing a Fan Tray from the Front

Summary of Contents for Catalyst 9400 Series

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands