manualshive.com logo in svg

Cisco Catalyst 9400 Series, Hardware Installation Manual

Share
Download
Cisco Catalyst 9400 Series Hardware Installation Manual Download Page 92

Enabling the Service Mode Before Removing a Fan Tray

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement

1030

Warning

No user-serviceable parts inside. Do not open.

Statement 1073

Warning

Enabling the service mode is a precautionary step that we recommend you complete, before you remove a
fan tray from the chassis. In the service mode, the system pushes the fans to operate at full speed for 10
minutes, allowing the system to cool down sufficiently and sustain temperatures for the duration of servicing.
The system automatically turns off (self-terminates) the service mode after 10 minutes.

Proceed with removing and replacing the fan tray immediately after the service mode self-terminates.

Important

• If the service mode is

not

enabled before servicing, only

two

minutes of fan-less operation can be safely

assured in a normal environment.

• If the service mode is enabled prior to servicing,

four

minutes of fan-less operation can be assured for

all normal operating conditions, at full traffic load, in any configuration.

In a system that is operational, enabling the service mode applies to removal or replacement procedures from
the front and the rear.

You do not have to enable this mode if you are removing and replacing the fan tray in a system that is not
powered on. The service mode is also not required if the fan tray is being replaced for having two or more
bad individual fans, because the fan tray will already be running at full speed.

To enable the service mode, enter the

test platform hardware chassis fantray service-mode on

command

in the privileged EXEC mode. For example:

Device#

test platform hardware chassis fantray service-mode on

fantray service mode on

To turn off the service mode before the system-allotted 10-minute duration, enter the

test platform hardware

chassis fantray service-mode off

command in the privileged EXEC mode.

Removing a Fan Tray from the Front

When you remove a fan tray from the front, only the fan tray is removed, excluding the adapter. To remove
a fan tray from the front, follow the steps described here.

When removing the fan tray, keep your hands and fingers away from the spinning fan blades. Let the fan
blades completely stop before you remove the fan tray.

Statement 258

Warning

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

86

Removing and Replacing FRUs

Enabling the Service Mode Before Removing a Fan Tray

Summary of Contents for Catalyst 9400 Series

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands