manualshive.com logo in svg

Cisco Catalyst 9400 Series, Hardware Installation Manual

Share
Download
Cisco Catalyst 9400 Series Hardware Installation Manual Download Page 108

In the course of its operation the system may require more than one power supply installed and
supplying power. Should it become necessary to remove an active power supply unit from the
system, consult the user manual for proper system administration of available power. In order to
safely de-energize the power supply unit, the input power should first be turned off by activating
the rocker input power switch switch into the OFF state and the power cable physically disconnected
from the unit. The unit must then be removed from the slot and stowed safely away in a proper
antistatic bag. Care must be taken not to touch any of the exposed pins from the backplane connector.
When a replacement power supply unit is to be installed, its rocker switch must always be in the
OFF state and no input power cable be installed prior to inserting it into the slot. After the unit is
seated, the input power cable may then be installed and fastened securely before activating the input
power into the ON state with the rocker input power switch prior to energizing the unit.

Statement

1028

Warning

What to do next

Set the power supply aside and proceed with installing the new or replacement power supply module. Install
blank covers in all power supply bays that are to remain empty (C9400-PWR-BLANK). For information about
installing blank covers, see

Removing and Installing a Power Supply Blank, on page 125

Installing an AC-Input Power Supply Module

To install an AC-input power supply module, follow the steps described here.

Before you begin

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement

1030

Warning

No user-serviceable parts inside. Do not open.

Statement 1073

Warning

Ensure that you have installed the cable guide before you begin the procedure. This is to properly guide and
arrange the power cords that you will attach as part of the installation. Since there are two rows of power
supply bays, the cable guide ensures that the power cords from one row of power supplies do not interfere
with the removal or replacement of modules in another row.

Procedure

Step 1

Remove the replacement power supply from its shipping packaging.

Step 2

Verify that the replacement power supply power switch is in the off (0) position.

Step 3

If installed, remove the blank power supply cover from the empty power supply bay. For information about
removing blank covers, see

Removing and Installing a Power Supply Blank, on page 125

. Save the blank cover

for future use.

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

102

Removing and Replacing FRUs

Installing an AC-Input Power Supply Module

Summary of Contents for Catalyst 9400 Series

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands