Cisco Catalyst 9400 Series Hardware Installation Manual Download Page 171

Page: 171 / 192

Meaning

LED Color

LED

SFP or SFP+ port link is up but there is no
packet activity.

Green

SFP or SFP+ UPLINK STATUS

Triangular LEDs pointing up or down,
indicating the status of the corresponding
port.

SFP or SFP+ port link is up and indicating
packet activity.

Blinking Green

SFP or SFP+ link is disabled by the user,
that is, administratively down.

Amber

Hardware (PHY) has detected a faulty port
link.

Blinking Amber

Error packets are being detected on the port
link. The error packets could be bad Cyclic
Redundancy Check (CRC) packets, jumbo
packets, etc.

Alternating Green
and Amber

SFP or SFP+ port link is down.

Off

QSFP port link is up but there is no packet
activity.

Green

QSFP UPLINK STATUS

LEDs next to each QSFP port number,
indicating the status of the corresponding
port.

QSFP port link is up and indicating packet
activity.

Blinking Green

QSFP port link is disabled by the user, that
is, administratively down.

Amber

Error packets are being detected on the
QSFP port link. The error packets could be
bad Cyclic Redundancy Check (CRC)
packets, jumbo packets, etc.

Alternating Green
and Amber

QSFP port link is down.

Off

The port set is enabled.

Starting with Cisco IOS XE Fuji
16.8.1a, PORT SET ENABLED
LEDs for SFP or SFP+ ports are
supported.

Note

Green

PORT SET ENABLED

There are four such LEDs on the
supervisor module faceplate:

• One for port numbers 1 to 4 (G1).

• One for port numbers 5 to 8 (G2).

• One for port number 9 (G3).

• One for port number 10 (G4).

The port set is not enabled.

Off

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

165

LEDs

Cisco Catalyst 9400 Series Supervisor Module LEDs

Summary of Contents for Catalyst 9400 Series

































































































































































































Search results

Summary of Contents for Catalyst 9400 Series

Reviews:

Brands by name

Popular brands

Cisco Catalyst 9400 Series, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 9400 Series

Reviews:

Brands by name

Popular brands