Cisco Catalyst 9400 Series Hardware Installation Manual Download Page 101

Page: 101 / 192

Rear panel of the fan tray. Tighten the captive
installation screws on this side,

after

sliding the

fan tray in.

Front of the fan tray. Tighten the captive
installation screws on this side

before

sliding

the fan tray in.

Step 3

Place the fan tray assembly into the fan tray bay so it rests on the chassis. Lift the fan tray up slightly, aligning
the top and bottom guides.

Step 4

Slide the fan tray assembly into the chassis until the two captive installation screws make contact with the
chassis.

Step 5

Tighten the two captive installation screws on the rear to secure the fan tray assembly in the chassis.

Step 6

Verify that you have installed the fan tray correctly. See

Verifying Fan Tray Installation, on page 95

Verifying Fan Tray Installation

To verify that the new fan tray is installed correctly and is operating properly, follow these steps:

Before you begin

To check the operation of the fans, you should have powered up the chassis.

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

Removing and Replacing FRUs

Verifying Fan Tray Installation

Summary of Contents for Catalyst 9400 Series

































































































































































































Search results

Summary of Contents for Catalyst 9400 Series

Reviews:

Brands by name

Popular brands

Cisco Catalyst 9400 Series, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 9400 Series

Reviews:

Brands by name

Popular brands