manualshive.com logo in svg

Cisco Catalyst 9400 Series, Hardware Installation Manual

Share
Download
Cisco Catalyst 9400 Series Hardware Installation Manual Download Page 168

Power Supply LEDs

AC Power Supply works when the AC input voltage is greater than 85 V. For normal operation, the INPUT
LED on AC Power Supply should be solid green. If the INPUT LED on AC Power Supply is blinking green
or off, check the AC power supply status. For more information, refer

Troubleshooting an AC-Input Power

Supply, on page 132

DC power supply works when DC input voltage is greater than 40 V. For normal operation, the INPUT LED
on DC Power Supply should be solid green. If the INPUT LED on DC Power Supply is blinking green or off,
check the DC power supply status. For more information, refer

Troubleshooting a DC-Input Power Supply,

on page 133

Note

Table 24: Cisco Catalyst 9400 Series Power Supply LEDs

Meaning

LED Colour

LED type

AC input voltage is 70 V minimum.

DC input voltage is -40 V minimum.

Green

INPUT

AC input voltage is less than 70 V.

DC input voltage is less than -40 V.

Off

AC input voltage is between 70 V and 85 V.

DC input voltage is between -37 V and -41 V.

Blinking Green

55 VDC power supply output and power supply
modules are operating within regulation limits.

Green

OUTPUT

Standby mode or sleep mode.

Blinks on for 0.5 seconds and off for 0.5 seconds.

Blinking Green

DC output voltages have not exceeded the alarm
threshold ranges.

Off

FAIL

An output voltage is out of the specified range, or the
power supply module's fan has failed (as sensed by
lack of fan rotation), or the power supply module is
turned off after input power is applied.

Illuminates for 2-3 seconds after input is applied or
disconnected through the front panel On/ Off rocker
switch (for AC-input power supplies) or On/ Off
power button (for DC-input power supplies) or a
circuit breaker.

Red

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

162

LEDs

Power Supply LEDs

Summary of Contents for Catalyst 9400 Series

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands