Cisco Catalyst 6880-X Hardware Installation Manual Download Page 23

Page: 23 / 124

Table 6: Fixed and Modular Card Ports LED Indicators

Description

Color/State

Port is not provisioned.

Off

Port is provisioned, but administratively not operational.

Amber

Port is linked up.

Green

A port fault is detected, or the port beacon has been provisioned by the
operator.

Alternating green and amber

Related Topics

LED Indicators, on page 8

Management Port LED

This table describes the management port LEDs.

Description

Color/State

Port is not provisioned.

Off

Port is provisioned, but administratively not operational.

Amber

Port is linked up.

Green

A port fault is detected, or the port beacon has been provisioned by
the operator.

Alternating green and amber

Related Topics

LED Indicators, on page 8

Catalyst 6880-X Switch Hardware Installation Guide

OL-30827-02

Product Overview

LED Indicators

Summary of Contents for Catalyst 6880-X





























































































































Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands

Cisco Catalyst 6880-X, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands