Cisco Catalyst 6880-X Hardware Installation Manual Download Page 76

Page: 76 / 124

Figure 26: Modular Port Card (C6880-X-LE-16P10G and C6880-X-16P10G)

Extraction handle

16 SFP+ or 100BASE-FX SFP ports

Port card

Status LED

ID (blue beacon LED)

Port LEDs

For a list of supported SFP and SFP+ modules, see the switch data sheet:

http://www.cisco.com/c/en/us/

products/collateral/switches/catalyst-6880-x-switch/data_sheet_c78-728228.html

Modular Port Card LEDs

For information on the modular port card LEDs, see these sections :

•

SFP+ Port LEDs, on page 10

•

Status LED on the Modular Port Card, on page 9

•

ID LED on the Modular Port Card, on page 10

Catalyst 6880-X Switch Hardware Installation Guide

OL-30827-02

Installing the Modular Port Card

Modular Port Card LEDs

Summary of Contents for Catalyst 6880-X





























































































































Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands

Cisco Catalyst 6880-X, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands