Cisco Catalyst 6880-X Hardware Installation Manual Download Page 78

Page: 78 / 124

Step 3

Remove the modular port card from the protective packing.

Step 4

Press the lever on the extraction handle to release the latch, and rotate the handle outwards.

Figure 28: Pressing the Lever on the Port Card

Step 5

Insert the port card into the chassis. Slide the port card into the slot until the back of the port card faceplate
is flush with the chassis faceplate.

Figure 29: Installing the Modular Port Card

Step 6

Close the latch on the extraction handle by pressing the lever until you hear a click, and it latches.

Catalyst 6880-X Switch Hardware Installation Guide

OL-30827-02

Installing the Modular Port Card

Installing a Modular Port Card

Summary of Contents for Catalyst 6880-X





























































































































Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands

Cisco Catalyst 6880-X, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands