Cisco Catalyst 6880-X Hardware Installation Manual Download Page 45 | Manualshive

Page: 45 / 124

background image

C H A P T E R

3

Installing the Switch

This chapter describes how to install a Catalyst 6880-X switch. Pointers within the overall chassis installation
procedures point to separate installation procedures that cover installing various components and assemblies.

•

Installation Tasks, page 33

•

Safety Warnings, page 34

•

Rack-Mounting Guidelines, page 35

•

Unpacking the Switch, page 36

•

Chassis Installation Kits and Cable Guides, page 36

•

Installing the Switch Chassis, page 37

Installation Tasks

The process of installing the switch can be broken down into a series of tasks, which are described in the
following table.

Description

Task

Remove the switch from the packaging materials.

Save the packaging material for later use if
you need to move the chassis.

Note

Unpacking the switch

The Catalyst 6880-X chassis can be rack-mounted.

Installing the switch

Construct and attach a system ground wire from the
building (earth) ground to the system ground point
on the chassis.

Connecting the chassis to system ground

Power supplies that are ordered with the switch are
installed in the switch. If ordered separately, install
the power supplies. Connect the power supplies.

Installing and cabling the power supply or supplies

Catalyst 6880-X Switch Hardware Installation Guide

OL-30827-02

33

«
...
43
44
45
46
47
...
»

Summary of Contents for Catalyst 6880-X





























































































































Reviews:

No comments

Related manuals for Catalyst 6880-X

Brand: Talkswitch Pages: 17

Brand: E-Trailer Pages: 8

Brand: Alyseum Pages: 7

Brand: Danfoss Pages: 6

Brand: GHIELMETTI Pages: 12

EdgePoint EP-S16

Brand: Ubiquiti Pages: 22

Brand: GBC Pages: 2

MIEN2208 Series

Brand: Maiwe Pages: 5

Brand: 3onedata Pages: 2

Unified Gigabit Wireless PoE Switch 24...

Brand: 3Com Pages: 40

Brand: Woxcon Pages: 42

Brand: Key Digital Pages: 20

Brand: Icy Box Pages: 12

Brand: National Instruments Pages: 23

Brand: Samson Pages: 48

GEF-UHD-89-HBT2

Brand: Gefen Pages: 232

Brand: 3Com Pages: 104

Brand: Exsys Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands