Cisco Catalyst 6880-X Hardware Installation Manual Download Page 21

Page: 21 / 124

Management Port LED, on page 11

Fan Tray LEDs, on page 12

AC-Input Power Supply LEDs, on page 13

DC-Input Power Supply LEDs, on page 14

System Status LED

The system status LED indicates the status of the system.

Table 2: System Status LED Indicator

Description

Color/State

System is not operational.

Off

System operating normally without alarms.

Green

System has triggered a minor environmental alarm.

Amber

System has triggered a major environmental alarm.

Red

Related Topics

LED Indicators, on page 8

Status LED on the Modular Port Card

The Status LED indicates the status of the modular port card.

Table 3: Status LED Indicator

Description

Color/State

Port card is not operational.

Off

Port card is operating normally without alarms.

Green

Port card has triggered a minor environmental alarm.

Amber

Port card has triggered a major environmental alarm, or the system is powering
up.

Red

System ID LED

The System ID (blue beacon) LED can be provisioned by the operator to indicate that the switch needs
attention.

Catalyst 6880-X Switch Hardware Installation Guide

OL-30827-02

Product Overview

LED Indicators

Summary of Contents for Catalyst 6880-X





























































































































Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands

Cisco Catalyst 6880-X, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands