Cisco Catalyst 6880-X Hardware Installation Manual Download Page 56

Page: 56 / 124

Figure 17: Installing the Cable Mount Guides

10-32 or 12-24 screws

What to Do Next

After installing the chassis in its location, complete the installation process by following these procedures:

•

Connecting the chassis to system ground. See

Establishing the System Ground, on page 45

•

Installing and connecting the power supplies to source power. For information on how to install and
cable power supplies, see the

Installing Power Supplies, on page 55

•

Connecting to the switch console port. See

Connecting the Switch Console Port, on page 47

•

Connecting to the uplink ports.

•

Powering-up the chassis and verifying the installation. See

Verifying Switch Chassis Installation, on

page 51

Catalyst 6880-X Switch Hardware Installation Guide

OL-30827-02

Installing the Switch

Rack-Mounting the Chassis

Summary of Contents for Catalyst 6880-X





























































































































Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands

Cisco Catalyst 6880-X, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 6880-X

Reviews:

Related manuals for Catalyst 6880-X

Brands by name

Popular brands