CID TRBC162672 Owner'S Manual Download Page 3

Page: 3 / 68

Copyright © 2022 Construction Implements Depot, Inc. All Rights Reserved. This manual may
not be reproduced or copied, in part or in whole without written permission from CID, Inc.

TRBCMAN01 / FIRST EDITION / MAY 2022

MODEL COMPARISON

TRBC162672 / TRBC162678

• 72” or 78” wide cut width

• 5” cut capacity

• 16-26 GPM direct drive motor

• No case drain required

• 3x AR400 non-welded blades

• Replaceable skid shoes

• Optional Mulching Teeth x12

• Optional Reaper Grill

TRBC172772 / TRBC172778

• 72” or 78” wide cut width

• 7” cut capacity

• 17-27 GPM direct drive motor

• Case drain required

• 3x AR400 non-welded blades

• Replaceable skid shoes

• Optional Mulching Teeth x12

• Optional Reaper Grill

SCAN these QRS (Quick Reference)

Codes to view this manual on your

smart phone or file a warranty claim.

WARRANTY INFO

OWNER'S MANUAL

Summary of Contents for TRBC162672





































































Search results

Summary of Contents for TRBC162672

Reviews:

Related manuals for TRBC162672

Brands by name

Popular brands

CID TRBC162672, Owner'S Manual

Search results

Summary of Contents for TRBC162672

Reviews:

Related manuals for TRBC162672

Brands by name

Popular brands