Chrysler 200 Convertible 2014 User Manual Download Page 564

Page: 564 / 610

4. Squeeze the two tabs on the side of the bulb socket and

pull straight out from the lamp assembly.

5. Disconnect the bulb from the wiring connector and

install the replacement bulb.

6. Install the bulb and connector assembly straight into

the lamp until it locks in place.

7. Install the turn signal bulb cap in the headlamp

housing and rotate clockwise to lock in place.

Rear Backup Lamp And Turn Signal Lamps

1. Open the trunk.

2. Remove the trunk trim by removing the grocery hook

(using a T-20 torque driver or similar tool), remove the
fastener, and pull back the weather strip.

3. Pull back the trunk liner to gain access to the tail lamp

wing nuts.

4. Remove the three wing nuts from the back of the tail

lamp assembly.

5. Pull the tail lamp assembly away from the vehicle

enough to access the electrical connector.

6. Push the electrical connector locking tab to the side.

7. Disconnect the electrical connector.

8. Continue removing lamp from vehicle in order to

access the bulb(s).

9. Turn the appropriate bulb and socket assembly coun-

terclockwise to remove it from the tail lamp assembly.

10. Disconnect the bulb from the socket assembly and

install the replacement bulb.

11. Reinstall the bulb and socket assembly into the tail

lamp assembly, and then turn it clockwise.

562

MAINTAINING YOUR VEHICLE

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 200 Convertible 2014

Reviews:

Chrysler 200 Convertible 2014, User Manual, Page: 564 / 610

Search results

Summary of Contents for 200 Convertible 2014

Reviews: