manualshive.com logo in svg

Chrysler 200 Convertible 2014, User Manual, Page: 379 / 610

Share
Download
Chrysler 200 Convertible 2014 User Manual Download Page 379

After Starting

The idle speed is controlled automatically and it will
decrease as the engine warms up.

ENGINE BLOCK HEATER – IF EQUIPPED

The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a
standard 110-115 Volt AC electrical outlet with a
grounded, three-wire extension cord.

The engine block heater must be plugged in at least one
hour to have an adequate warming effect on the engine.

The engine block heater cord is routed under the hood on
the driver side of the vehicle. It has a removable cap that
is located on the driver side of the Integrated Power
Module.

WARNING!

Remember to disconnect the engine block heater
cord before driving. Damage to the 110-115 Volt
electrical cord could cause electrocution.

AUTOMATIC TRANSMISSION

CAUTION!

Damage to the transmission may occur if the follow-
ing precautions are not observed:

•

Shift into PARK only after the vehicle has come to
a complete stop.

•

Shift into or out of REVERSE only after the vehicle
has come to a complete stop and the engine is at
idle speed.

(Continued)

5

STARTING AND OPERATING

377

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Reviews:

No comments