Chrysler 200 Convertible 2014 User Manual Download Page 528

Page: 528 / 610

2. Unsnap both ends and lift the filter access cover.

3. Remove the used filter.

4. Install the new filter with arrows pointing in the

direction of airflow, which is toward the rear of the
vehicle (text and arrows on the filter will indicate this).

5. Close the filter access cover.

Refer to the “Maintenance Schedule” for the proper
maintenance intervals.

Filter Access Cover

A/C Air Filter

526

MAINTAINING YOUR VEHICLE

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 200 Convertible 2014

Reviews:

Chrysler 200 Convertible 2014, User Manual, Page: 528 / 610

Search results

Summary of Contents for 200 Convertible 2014

Reviews: