manualshive.com logo in svg

Chrysler 200 Convertible 2014, User Manual, Page: 499 / 610

Share
Download
Chrysler 200 Convertible 2014 User Manual Download Page 499

CAUTION!

Do not use a portable battery booster pack or any
other booster source with a system voltage greater
than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.

WARNING!

Do not attempt jump-starting if the battery is frozen.
It could rupture or explode and cause personal injury.

Preparations For Jump-Start

The battery is stored under an access cover in the trunk.
Remote battery posts are located on the right side of the
engine compartment for jump-starting.

Remote Battery Post Locations

1 — Remote Positive

(+)

Post

2 — Remote Negative

(-)

Post

6

WHAT TO DO IN EMERGENCIES

497

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Reviews:

No comments