manualshive.com logo in svg

Chrysler 200 Convertible 2014, User Manual, Page: 483 / 610

Share
Download
Chrysler 200 Convertible 2014 User Manual Download Page 483

Cooling System

To reduce potential for engine and transmission over-
heating, take the following actions:

City Driving

When stopped for short periods of time, shift the trans-
mission into NEUTRAL and increase engine idle speed.

Highway Driving

Reduce speed.

Air Conditioning

Turn off temporarily.

RECREATIONAL TOWING
(BEHIND MOTORHOME, ETC.)

Two-Wheel Drive And All-Wheel Drive

Recreational towing (with all four wheels on the ground,
or using a tow dolly) is

NOT ALLOWED

. The only

acceptable method for towing this vehicle (behind an-
other vehicle) is on a vehicle trailer with all four wheels

OFF

the ground.

CAUTION!

Towing this vehicle in violation of the above require-
ments can cause severe transmission and/or transfer
case damage. Damage from improper towing is not
covered under the New Vehicle Limited Warranty.

5

STARTING AND OPERATING

481

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Reviews:

No comments