manualshive.com logo in svg

Chrysler 200 Convertible 2014, User Manual, Page: 32 / 610

Share
Download
Chrysler 200 Convertible 2014 User Manual Download Page 32

•

The engine can be started two consecutive times (two
15-minute cycles) with the RKE transmitter. However,
the ignition must be cycled to the RUN position before
you can repeat the start sequence for a third cycle.

To Exit Remote Start Mode Without Driving The
Vehicle

Press and release the REMOTE START button one time or
allow the engine to run for the entire 15 minute cycle.

NOTE:

To avoid unintentional shutdowns, the system

will disable the one time press of the REMOTE START
button for two seconds after receiving a valid Remote
Start request.

To Exit Remote Start Mode And Drive The Vehicle

Before the end of 15 minute cycle, press and release the
UNLOCK button on the RKE transmitter to unlock the

doors and disarm the Vehicle Security Alarm (if
equipped). Then, prior to the end of the 15 minute cycle,
press and release the START/STOP button.

NOTE:

The message “Push Start Button” will display in

the EVIC until you push the START button.

DOOR LOCKS

Manual Door Locks

To lock each door, push the door lock knob on each door
trim panel downward. To unlock the front doors, pull the
inside door handle to the first detent. To unlock the rear
doors, pull the door lock knob on the door trim panel
upward.

30

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Reviews:

No comments