manualshive.com logo in svg

Chrysler 200 Convertible 2014, User Manual, Page: 201 / 610

Share
Download
Chrysler 200 Convertible 2014 User Manual Download Page 201

(22.7 mm and 67.7 mm) forward of the rear stop. The
seat will return to its previously set position when you
place the ignition to the ACC or RUN position.

•

The Easy Entry/Easy Exit feature is disabled when the
driver seat position is less than 0.9 in (22.7 mm)
forward of the rear stop. At this position, there is no
benefit to the driver by moving the seat for Easy Exit
or Easy Entry.

Each stored memory setting will have an associated Easy
Entry and Easy Exit position.

NOTE:

The Easy Entry/Easy Exit feature can be enabled

or disabled using the Uconnect® System, refer to
“Uconnect® Settings” in “Understanding Your Instru-
ment Panel” for further information.

TO OPEN AND CLOSE THE HOOD

Two latches must be released to open the hood.

1. Pull the hood release lever located under the left side

of the instrument panel.

Hood Release Lever

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

199

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Reviews:

No comments