manualshive.com logo in svg

Chrysler 200 Convertible 2014, User Manual, Page: 118 / 610

Share
Download
Chrysler 200 Convertible 2014 User Manual Download Page 118

BLIND SPOT MONITORING (BSM) —
IF EQUIPPED

The Blind Spot Monitoring (BSM) system uses two radar-
based sensors, located inside the rear bumper fascia, to
detect highway licensable vehicles (automobiles, trucks,
motorcycles, etc.) that enter the blind spot zones from the
rear/front/side of the vehicle.

When the vehicle is started, the BSM warning light will
momentarily illuminate in both outside rear view mirrors
to let the driver know that the system is operational. The
BSM system sensors operate when the vehicle is in any
forward gear or REVERSE and enters stand by mode
when the vehicle is in PARK.

Rear Detection Zones

116

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Reviews:

No comments